How To Install A Backup Camera On A Pickup Truck

Download Article

Download Article

A rear-view camera, as well known as a backup camera, lets yous see what's behind your vehicle without having to await backwards. Though the device comes standard with many new car models, yous can add a rear-view photographic camera to your vehicle if information technology didn't come with one.

1. 1

   Buy a mountable fill-in photographic camera for your specific vehicle. For safety, make sure you purchase a device specifically designed to be a rear-view camera. Purchasing one fabricated for your specific vehicle volition make it easier to install than a standard aftermarket photographic camera. So yous tin install information technology hands, look for a camera that mounts onto or directly behind your license plate.^[1]

   • Look for fill-in cameras at consumer electronics stores.

2. 2

   Get an external monitor if y'all want to keep your existing rear-view mirror. An external backup monitor is a small video screen that mounts onto your windshield similarly to a GPS. Though they have upward more than space than internal monitors, external monitors are far easier to see and can be easily replaced if necessary.

   • If you'd similar, yous tin can employ a standard video monitor instead. Withal, keep in mind that it may non accept all the aforementioned features every bit devices designed for employ with backup cameras.

   Ad

3. iii

   Purchase an internal monitor for a less obtrusive device. An internal backup monitor is a fully operation rear-view mirror that houses a small screen inside the glass. Some internal monitors clip on tiptop of your current rear-view mirror, but others replace your original mirror entirely.^[2]

   • Nearly internal monitors shut off and disappear when not in use, making them a perfect selection if you want to preserve your motorcar's looks.

4. 4

   Buy power and video cords if your camera and monitor didn't include them. For most rear-view camera installations, you lot'll need camera and monitor splitter cords with connectors for video and power cables, 2 bare wire power cables, and an RCA video cable.^[3]

   • Virtually installation kits include these cables, but some may require you to purchase them separately.
   • Some camera models utilize wireless transmitters instead of standard video cables.

   Advertisement

1. one

   Take off your rear license plate. Using a Phillips caput screwdriver, remove each of the screws belongings your rear license plate in place. And so, pull the plate off and prepare it bated.^[4]

   • Make certain you lot place the screws in a safe identify so you don't lose them.

2. 2

   Remove your torso'southward interior panel. Pop open your trunk and expect for a solid interior panel covering the opposite side of your license plate mounting area. And so, insert a trim removal tool or other thin device behind the console and pry it off.^[5]

   • Removing this panel volition expose the car's rear wiring chambers.

3. iii

   Drill a modest hole in the license plate mounting surface area. Make sure at that place are no obstructions betwixt the license plate mount and the rear wiring chamber. Then, create a small hole in the auto using a power drill equipped with a high-speed twist drill fleck. Line upward your hole so it is directly behind where your photographic camera's power and video cablevision will go.^{[half dozen]}

   • To effigy out where to make the hole, concur your camera upwardly to the area you intend to mount it. Then, note the spot where its splitting cord sits.
   • Create a pigsty that's big plenty to fit your camera'south power and video cable.
   • If y'all come up across any obstructions, try to remove them. If you can't, see if you lot can make a hole nearby.
   • For most jobs, yous'll demand a drill fleck that has a bore betwixt ¹⁄₈ and ¹⁄_iv  in (0.32 and 0.64 cm).

4. 4

   Identify a rubber grommet around your photographic camera cable. Before running your camera cable into the automobile, slip a prophylactic grommet onto information technology near the not-splitting end. These small prophylactic washers, available at most home improvement stores, volition keep the wire in identify and prevent leaks.^[vii]

   • Choose a grommet that'due south merely large enough to fit inside the drilled hole.

5. v

   Run the camera cable into your body. Pull the splitting terminate of your camera's video and power cablevision through the drilled hole into the torso of your car. Make certain you lot pull it tight so the prophylactic grommet lodges into the drilled pigsty.

   • Your photographic camera cablevision should run from the outside of the car to the inside of the car.

6. six

   Locate your machine's 2 reverse low-cal wires. Reverse light wires are the cords that connect your machine's tail lights to the dashboard. They hook directly into your vehicle's tail lights and are normally located in the hatch or trunk of your automobile.

   • These cords wait different for every vehicle so, if you lot can't observe them, consult your owner'southward manual for model specific information.

7. seven

   Strip and separate your car's reverse light wires. Using a wire stripper or pliers, skin back the rubber covering the wires. Then, use a screwdriver or other thin tool to poke a pigsty through the middle of each exposed wire, separating the private wire strands.^[8]

   • For safety, make sure you do this while the car is turned off.

8. 8

   Fuse your camera wires with the opposite light wires. Adhere 1 of your bare wire cables to the camera cord's power connector. And so, poke your bare wires through the middle of the exposed opposite light wires and twist them together. For safety, brand sure yous wrap the combined wires in electrical tape.^[9]

   • Brand sure you poke your positive (usually ruddy) blank wire through the positive contrary calorie-free wire and the negative (usually black) bare wire through the negative reverse lite wire.

   Advertisement

1. i

   Route your camera's video cable to the front end of the car. Connect your RCA cablevision to the camera cord's video connector if necessary. Then, run it through your vehicle to the expanse by the fuse box. Depending on your vehicle model, you'll commonly be able to practise this past peeling dorsum the automobile's headliner or side panels and pulling your cable through the exposed chamber.^[x]

   • For certain trucks, you may need to run the video cablevision through the vehicle's frame rail.
   • In most cars, you'll find the fuse box underneath the steering wheel.

2. ii

   Fix external monitors to the front end windshield. If you lot're installing an external monitor, start adhere your device'south included mount to the windshield by following the manufacturer'south included instructions. And so, hook your monitor onto the mount.

   • Well-nigh external monitors use a suction mount, though others may come up with a more complex mounting system.

3. 3

   Attach internal monitors to the rear-view mirror or mirror mount. For sure internal monitors, you'll need to clip the new device onto your current rear-view mirror. For others, you lot'll need to take off the mirror and slide your monitor into the pre-existing mirror mountain.^[11]

   • Some internal monitors may come with their own mounting system that you'll have to attach to the machine's front windshield.

4. 4

   Run the monitor'due south splitter cablevision to the fuse box. If necessary, claw your monitor'south ability and video cable into the device. Then, route the cablevision from the monitor to the surface area side by side to the fuse box.^[12]

   • If you'd like, use a trim removal tool to pop out the headlining panel straight in a higher place your windshield. Then, run your cable through the exposed chamber.

5. 5

   Connect your monitor's camera cable to the RCA cable. After routing your monitor'southward splitter cable, connect the video finish of the cable to your camera's RCA cord. And so, wrap the connected cords with electrical record to concur them together.

   • If your RCA and video cables take the same ends, you may need to purchase an RCA male to female converter cord. You can find these at most electronic stores.

6. 6

   Adhere your monitor's ability cable to a fuse tap. Connect your remaining bare wire cable to the backup monitor'due south power cord. Then, push the positive (usually red) end of the bare wire cablevision into the open end of a fuse tap. Finally, crimp the two cables together with a pair of pliers.^[13]

   • A fuse tap is a small-scale cable that converts a bare wire into a fuse betoken. You can discover them at most auto part stores.
   • If you'd prefer, you lot tin exit the bare wire cable off and connect your photographic camera's power cable to a cigarette lighter adaptor. Then, plug this adaptor into your car'southward cigarette lighter receptacle for power.

7. 7

   Plug the fuse tap into the fuse box. Locate your fuse box and open up information technology up. Then, plug your fuse tap into an open fuse cell. If necessary, check your fuse box's lid or your vehicle's teaching manual to encounter which slots are open up.^[fourteen]

   • Afterward attaching your fuse, consider taping all your wires together using electric record to become them out of the manner.

   Advertizing

1. i

   Connect your backup photographic camera to its power and video cablevision. Render to the back of your car in one case y'all've installed the rear-view monitor and all the necessary camera cords. Close the body if necessary, then connect the backup camera to its power and video cable.

   • Your camera'due south power and video cablevision should be sticking out of the hole you lot drilled in the license plate mounting area.

2. 2

   Mountain the camera to your license plate. If the camera attaches to the forepart of your license plate, fix it to the plate by following the manufacturer'southward included instructions. If the camera attaches to the back of your license plate, line the device upward with the plate'southward fastener holes and thread screws through them.^[15]

   • In well-nigh cases, you can attach a rear-view photographic camera to the dorsum of your license plate using the screws you removed from the car earlier.

3. three

   Reattach your license plate and trim panels. Using a Phillips caput screwdriver, put your rear license plate dorsum on your vehicle. Once you've reattached information technology, give the license plate and backup camera firm tugs to make sure they're secure.

   • If you oasis't already, reattach your auto's interior trunk panel and other trim panels by pressing them back onto the vehicle.

4. 4

   Test the camera to make sure everything works. Before using your new camera on public roads, exam information technology in a safe area similar your driveway. If it turns on, place a large, durable object similar a trash can behind the camera to meet how distorted the image is. If it does non turn on, read your installation manual for troubleshooting information.

   • In many cases, rear-view camera malfunctions are caused by loose or improperly connected wires.

   Advertisement

Add New Question

• Question

  I hooked the camera up and information technology just flickers. Any advice?

  

  You may want to ensure all cables and connections are secured tightly. Double check that all connections are correct. If this doesn't work, cheque to encounter if the camera chosen is in practiced shape and isn't physically damaged.

• Question

  Suzuki installed contrary parking camera in my Swift Dzire Zxi. Only the camera shows upper view and not the ground below. What can I practise ?

  

  Make sure that the camera is installed the correct way (non upside downwardly), and check the position of the camera mounted. Take it back to the dealer that installed information technology and inquire them to check the alignment and fit.

• Question

  What is the best tiptop for a reversing camera?

  

  In that location is no optimal tiptop for a back-upwards camera. The platonic height is based off the specific auto or vehicle that you accept and your personal preferences, along with its intended application. Some back-up cameras are placed on large service trucks and so that they can line up to trailer hitches easier, some are to prevent a blindspot on the road. Depending on your awarding, it tin exist placed at any height. Most reversing cameras are a "wide view" way and the specific height location does not ever affect the way information technology functions.

Ask a Question

200 characters left

Include your email accost to go a message when this question is answered.

Submit

Advertizing

• Though most car dealers and mechanics volition non install aftermarket fill-in camera systems, many audio and electronic shops will.

Advertisement

• Brand sure you plough the machine off before working with bare or stripped wires. If yous demand to touch exposed wires while the car is on, put on a pair of shock-resistant safe gloves.

Advert

Things You'll Demand

• Rear-view camera
• Rear-view monitor
• Connector cables
• Phillips head screwdriver
• Trim removal tool
• Ability drill with loftier-speed twist bit
• Rubber grommet
• Wire stripper or pliers
• Electrical tape
• Fuse tap

Nigh This Article

Commodity Summary X

To successfully install a rear-view camera, first remove your vehicle'southward rear license plate and interior body panel. Using a power drill, dial a modest hole through the exposed license plate mounting area and run your camera's power and video cord through information technology. Adhere a bare wire power cable to your camera'southward power connector, then strip your car's reverse low-cal wires and splice them with your bare wire power cablevision. To acquire how to mount the rear-view camera and fill-in monitor, gyre down!

Did this summary help yous?

Thank you to all authors for creating a page that has been read 246,511 times.

Did this commodity assist yous?

Source: https://www.wikihow.com/Install-a-Rear-View-Camera

Posted by: cotecauseveras1987.blogspot.com

Share this post